Tuesday, August 30, 2016

General-purpose Zener diode NZX7V5B

Zener diode NZX7V5B (7.4V, 500mW)  in a SOD27 (SC-40) small hermetically sealed glass package.

DC to DC Boost Converter Step-Up Output 5V-35V

DC-DC Boost Converter Step-Up Power Module Output 5V-35V
Module DC-DC voltage booster is equipped with a chip XL6009E1 2nd generation with high-frequency switching technology.

specifications:
- Input voltage: 3V - 32V
- Max input Current : 4Amp
- Output voltage: 5V - 35V
- Equipped 4A MOSFET switch tube, so that the level of efficiency can be achieved up to 94%
- The switching frequency up to 400 Khz
- Dimensions: 43mm x 21mm x 14mm

36 pin Male Centronic Connector

Centronic 36 pin Male Connector
36 pin connector to the cable (IDC Socket / flops)
specifications:
- Production Centronic
- The number of pins: 36-pin
- Configure Printer Port connector according to the 36-pin

Monday, August 29, 2016

MPC17529EVEL cmos motor driver

Bipolar CMOS motor drivers are equipped with the technology under voltage detection and shutdown circuit.

  • Motor Type - Stepper Bipolar
  • Motor Type - AC, DC Brushed DC
  • Function Driver - Fully Integrated, Control and Power Stage
  • Output Configuration Half Bridge (4)
  • Interface Parallel
  • Technology CMOS
  • Applications Battery Powered
  • Current - Output 700mA
  • Voltage - Supply 2.7 V ~ 5.6 V
  • Voltage - Load 2 V ~ 6.8 V
  • Operating Temperature -20°C ~ 150°C (TJ)
  • Mounting Type Surface Mount
  • Package / Case 20-SSOP (0.209", 5.30mm Width)
  • Supplier Device Package 20-VMFP

DF02STRR16 1Amp bridge rectifier diode

1 Ampere diode bridge/rectifier with a maximum voltage of 200 Volt
  • Bridge Rectifiers 1-PHA 200V 1A D-71
  • Current of 1 A
  • 4- SMD packaging (DFS)
  • Input peak voltage of 200 V (Max)

UART Fingerprint Reader

UART Fingerprint Reader is a fingerprint reader module with stability and high speed identification (High speed identification and high stability), because it uses a processor STM32F205. This module is one intelligent module that has a variety of functions such as fingerprint recording, image processing, feature extraction, template generation, template storage, Finger matching and Searching


Sunday, August 28, 2016

ADM3202ARUZ transceiver IC (RS-232 2-channel)

ADM3202ARUZ is transceiver IC (RS-232 2-channel) hi-speed  who works at a level 3 - 5.v volts.

specifications:
- Function: RS-232 Transceivers Full Duplex
- Data Rate: 460 kb / s
- Number of Drivers: 2 drivers
- Number of Receivers: 2 Receiver
- Operating Supply Voltage: 3 V to 5.5 V
- Operating Supply Current: 3 mA
- Operating Temperature: - 40 ° C s / d + 85 ° C
- Number of Transceivers: 1 Transceiver
- Protocol Supported: RS-232
- Receiver Signal Type: Single-Ended
- Supply Type: Single Supply
- Packaging: TSSOP-16

SI-8050S Step Down 5V Switching Regulator chip

ALLEGRO SANKEN SI-8050S Buck (Step Down) Switching Regulator, Fixed, 7V-40V In, 5V And 3A Out, TO-220F-5
The SI-8050S is a full-mould separate excitation Switching IC with phase correction and output voltage adjustment performed internally. The SI-8000S series IC has built-in reference oscillator (60kHz), built-in over-current and thermal protection circuits and built-in soft start circuit (output ON/OFF control).
  • 79 to 91% High efficiency
  • Requires only 4 external components
Tech Specs:
  • Input Voltage Min: 7V 
  • Input Voltage Max: 40V 
  • DC / DC Converter IC Case: TO-220F 
  • No. of Pins: 5Pins 
  • Output Current: 3A 
  • Output Voltage Nom.: 5V 
  • Switching Frequency: 60kHz 
  • Topology: Buck (Step Down) 
  • Operating Temperature Max: 125°C

Transistor PNP 2N4125

General purpose Transistor PNP 2N4125

  • Packaging TO-92
  • Type PNP Silicon Transistor
  • Max continuous collector current (ic) 200mA
  • Maximum collector-emitter voltage (VCE) 30V
  • Minimum base-collector voltage of the on-state (VBE) sat 0.95V (@ IC 50 mA, 5.0 mA IB)
  • Maximum saturation voltage collector-emitter (VCE) sat 0.4V (@IC 50 mA, 5.0 mA IB)
  • hfe 200

Friday, August 26, 2016

Active GPS antenna, MCX connector with cable 5 Meter

Active GPS antenna, MCX connector with cable 5 Meter

External GPS Antenna with Magnet, cable length of 5 meters and uses MCX connectors. Power Supply: 3.0V - 5.0V

Specs:
  • Cable Length 5 meters
  • Working frequency 1575.42 MHz
  • Voltage standing wave ratio (VSWR) 1.5: 1
  • The input impedance of 50 Ohm
  • ± 30dB Gain

916MHz Helical Antenna HT916

Helical antenna with working frequency 916MHz

W5E-WO-03L WiFi Dipole Antenna and Antenna Cable Assembly

Wiznet W5E-WO-03L WiFi Antenna Dipole Antenna and Cable Assembly
Antenna for 2.4GHz frequency -WiFi / WLAN / Bluetooth / Zigbee with Linear polarization.

Specs:
  • Dimensions 102.8 x 11 mm
  • The input impedance of 50 Ohm
  • Gain +/- 3.5 (dBi)

3dbi Wifi Antenna

Antenna for 2.4GHz frequency (WIFI) black. This antenna has a male SMA connector types, and there is a hinge that can be bent 90 degrees.

Specs:

  • Dimensions Height 110mm (straightened)
  • The operating frequency of 2.4 GHz / WIFI
  • Voltage standing wave ratio (VSWR) 1.5
  • The input impedance of 50 Ohm
  • Gain 3.0 dBi

Thursday, August 25, 2016

EGP50B-E3/54 ultrafast Diode 100V 5Amp

A voltage rectifier has the ability recovery very fast.

  • Current of 5 A
  • Packaging GP-20
  • Input voltage is 100 V peak

IRLZ24N N-Channel Hexfet, Power Mosfet

55V Single N-Channel HEXFET Power MOSFET in a TO-220AB package

  • Packaging TO-220-3
  • Polarity N-Channel
  • Power dissipation 45 W
  • Drain-source breakdown voltage 55 V
  • Gate-source voltage 16 V
  • Continuous drain current 18 A
  • Barriers drain-source rds (on) 105 Mohm

AT24C01D-PUM 1Kbit EEprom chip

The Atmel 1Kb 2-wire Serial EEPROM with Full Memory Write Protect, supports up to eight devices on a single 2-wire bus. The EEPROM is organized as 128 words x 8 bits. Optimized for industrial and commercial applications where low-power and low-voltage operations are essential. The EEPROM is available in space-saving packaging options and operates from 1.7V to 3.6V.
Key Parameters
ParameterValue

  • Operating Voltage (Vcc): 1.7 to 3.6
  • Interface Type: 2-wire
  • Density: 1Kb
  • Organization: 128 x 8
  • Page Size (Bytes): 8
  • Temp. Range (deg C): -40 to 85
  • Max. Operating Freq. (MHz): 1 MHz
  • I/O Pins: 5/8

BTN7971B half bridge motor driver

The BTN7971B is a integrated high current half bridge for motor drive applications. It is part of the NovalithIC™ family containing one p- channel highside MOSFET and one n- channel lowside MOSFET with an integrated driver IC in one package. Due to the p- channel highside switch the need for a charge pump is eliminated thus minimizing EMI. Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs, diagnosis with current sense, slew rate adjustment, dead time generation and protection against overtemperature, overvoltage, undervoltage, overcurrent and short circuit. The BTN7971B provides a cost optimized solution for protected high current PWM motor drives with very low board space consumption.

Summary of Features:

  • Path resistance of max. 30.5 mΩ @ 150 °C (typ. 16 mΩ @ 25 °C) High Side: max. 12.8 mΩ @ 150 °C (typ. 7 mΩ @ 25 °C) Low Side: max. 17.7 mΩ @ 150 °C (typ. 9 mΩ @ 25 °C)
  • Low quiescent current of typ. 7 μA @ 25 °C
  • PWM capability of up to 25 kHz combined with active freewheeling
  • Enhanced switching speed for reduced switching losses
  • Switched mode current limitation for reduced power dissipation in overcurrent
  • Current limitation level of 50 A min. / 70 A typ. (low side)
  • Status flag diagnosis with current sense capability
  • Overtemperature shut down with latch behavior
  • Overvoltage lock out
  • Undervoltage shut down
  • Driver circuit with logic level inputs
  • Adjustable slew rates for optimized EMI
  • Green Product (RoHS compliant)
  • AEC Qualified

Target Applications:
Motor-Drive

AD7705BNZ 2 channel ADC

ADC IC is a 2-channel, 16-bit Sigma-Delta for low frequency measurement applications.

  • Power supply 4,75V - 5,25V
  • DIP-16 Packaging
  • serial interface
  • 16 bit resolution
  • Number of channels 2

BC546 NPN

BC546 NPN bipolar transistor

  • Packaging TO-92
  • NPN
  • Max continuous collector current (ic) 100 mA
  • Minimum base-collector voltage of the on-state (VBE) sat 65 Volt
  • hfe 110

Tuesday, August 23, 2016

Neutrik NP3X Plug Audio TRS 1/4 inch Male

NP3X Neutrik 1/4 inch TRS Audio Plug Male
3 pole professional phone plug from Nuetrik highly suited for audio applications. This plug has contacts made of nickel and is protected by a shield made from nickel.


  • Plug terminal type, 3 pole
  • Shape (female / male) male
  • Pin number 3 pole
  • Cable mounting
  • Contact Material Nickel
  • Packaging materials Nickel

Monday, August 22, 2016

ACR1252U USB NFC Reader III (NFC Forum Certified Reader)

The ACR1252U USB NFC Reader III is an NFC Forum-certified PC-linked reader, developed based on 13.56Mhz contactless technology. It has a SAM (Secure Access Module) slot which can be used together with a SAM card for key diversification and mutual authentication, providing high-level security in contactless transactions. Post-deployment firmware upgrade is also supported, eliminating the need for additional hardware modification.

ACR1252U is capable of the three modes of NFC, namely: card reader/writer, card emulation and peer-to-peer communication. It supports ISO 14443 Type A and B cards, MIFARE®, FeliCa, and ISO 18092–compliant NFC tags. It also supports other NFC devices with an access speed of up to 424 Kbps and proximity operating distance of up to 50mm (depending on tag type used).

Compliant with both CCID and PC/SC, this plug-and-play USB NFC device allows interoperability with different devices and applications. It is thus ideal for unconventional marketing and advertising applications like smart posters.

The ACR1252U comes with an optional stand to hold the smart card reader at an optimal angle, so that users can tap contactless cards or NFC-enabled devices onto the ACR1252U with ease.

Features:

  • USB 2.0 Full Speed Interface  
  • CCID Compliance  
  • USB Firmware Upgradeability  
  • Smart Card Reader:  
  • Read/write speed up to 424 kbps  
  • Built-in antenna for contactless tag access, with card reading distance of up to 50 mm (depending on tag type)  
  • Supports ISO 14443 Type A and B cards, MIFARE, FeliCa, and all 4 types of NFC (ISO/IEC 18092) tags  
  • Supports MIFARE 7-byte UID, MIFARE Plus and MIFARE DESfire  
  • Built-in anti-collision feature (only 1 tag is accessed at any time)  
  • One ISO 7816–compliant SAM slot (Class A)  
  • NFC Support:  
  • NFC Reader/Writer Mode  
  • Peer-to-Peer Mode  
  • Card Emulation Mode  
  • Application Programming Interface:  
  • Supports PC/SC  
  • Supports CT-API (through wrapper on top of PC/SC)  
  • Peripherals:  
  • User-controllable bi-color LED  
  • User-controllable buzzer  
  • SAM Slot


Tech Info:
Dimensions98.0 mm (L) x 65.0 mm (W) x 12.8 mm (H)
Weight81.0 g
InterfaceUSB 2.0 Full Speed
Operating DistanceUp to 50 mm (depends on the tag type)
Supply VoltageRegulated 5V DC
Supply CurrentMax. 200mA
Operating Temperature0-50 °C
Operating Frequency13.56 MHz
Smart Card Interface Support
  • ISO 14443 Type A & B
  • MIFARE
  • FeliCa
  • 4 types of NFC (ISO/IEC 18092) tags
Compliance / Certifications
  • ISO 18092, ISO 14443, ISO 7816,  NFC Forum, FeliCa Performance Certification, PC/SC, CCID, LASCOM, EN60950/IEC 60950, CE, FCC, VCCI, MIC, KC, RoHS 2, USB Full Speed, Microsoft® WHQL
Operating System Support
  • Windows®
  • Linux®
  • Mac OS®
  • Android™ 3.1 and above
ACR1252U NFC reader III SDK
Applications:

  • e-Government
  • Banking & Payment
  • e-Healthcare
  • Network Security
  • Access Control
  • e-Purse & Loyalty
  • Transportation
  • Smart Poster
  • P2P Communication

Sunday, August 21, 2016

Neutrik NC3FXX 1/4 inch Female XLR Audio Jack

NC3FXX 1/4 inch Neutrik XLR Female Audio Jack

Female XLR connector types NC3FXX of Neutrik. These connectors use the materials for connectors and nickel silver for its protective packaging. This connector is usually used for Audio.

Specs:

  • Type XLR terminal
  • Shape (female / male) Female
  • Pin number 3 pole
  • cable mounting
  • Contact Material Silver
  • Packaging materials Nickel

Neutrik NC3MXX 1/4 inch Male XLR Audio Jack

NC3MXX 1/4 inch Neutrik XLR Male Audio Jack

Male XLR connector types NC3MXX of Neutrik. These connectors use the materials for connectors and nickel silver for its protective packaging. This connector is usually used for Audio.

Specs:

  • Type XLR terminal
  • Shape (female / male) male
  • Pin number 3 pole
  • cable mounting
  • Contact Material Silver
  • Packaging materials Nickel

SMD LED logic tester type B

SMD LED Logic Tester B is a display module for 8 bit parallel port which consists of eight LED SMD configuration with Active Low. Fully compatible with all ports MCS-51 Series Low Cost Low Cost Board and AVR Series Board is configured as an output.

specifications:
- Using the SMD components.
- 8 LED circuit configuration with Active Low.
- Compatible with MCS-51 Series Low Cost Low Cost Board and AVR Series Board.
- Can be used as a display output for program tester.
- Equipment: 1 piece Board SMD LED Logic Tester B, 1 sheet manual.

SMD LED logic tester type A

SMD LED logic tester type A
SMD LED Logic Tester A is a display module for 8 bit parallel port which consists of eight LED SMD configuration with Active Low. Fully compatible with the MCS-51 family MinSys Port1, porta, PortB, and Portc configured as an output.

specifications:
- Using the SMD components.
- 8 LED circuit configuration with Active Low.
- Compatible with MCS-51 MinSys ver 3.0 Board.
- Can be used as a display output for Tesport or TESPPI program.
- Equipment: 1 piece Board SMD LED Logic Tester A and 1 sheet manual.

Simple logic LED tester

Simple logic LED tester
a module consisting of 4 LEDs as output and 4 pieces of tactile switches as input. This module can be used as logic tester for input and output of the microcontroller port.

specifications:
- 4 LED configuration with active low (logic 0 on a port will activate LED).
- 4 tactile switches with active low configuration (tactile switch is pressed will produce a logic 0).
- Can be used on the port PPI (82C55) and port 1 MCS-51 microcontroller.

TDA2003V 10W audio amplifier chip

TDA2003V 10W audio amplifier chip
Audio amplifier with output power of 10W (RL = 2 ohms, f = 1kHz) and frequency response of 40 Hz to 15KHz.

Specs:

  • DC power supply 8V - 18V DC
  • Output current 3,5A
  • packaging Pentawatt
  • 40dB closed loop gain bandwidth (f1KHz), 80dB open loop (f1KHz) and 60dB (f10KHz)

Bridge Rectifier RS204-BP 400V/2Amp

Bridge Rectifier with the ability to skip a current of 2A.

  • The maximum current 2A
  • The maximum input voltage of 400 V

2.8 inch TFT LCD Touch Shield for Arduino

Display module with a size of 2.8 "that is compatible with Arduino.
Features:
- Resolution = 320 x 240.
- Interface standard Arduino (Arduino Uno, Arduino Leonardo, & XNucleo).
- There is a microSD slot, for the purposes of displaying photos.

Specs:
3.3 VDC power supply ?? 5VDC
Dimensions 73,3mm x 55,3mm
Interface SPI (Standard Arduino)
LCD Type TFT LCD (with resistive touch panel)
HX8347D Controller (LCD) & XPT2046 (Touch Screen)
View area 57,6mm x 43,2mm

Saturday, August 20, 2016

1N5921B , 6.8 V, 3.0 W Zener Diode Voltage Regulator

This is a complete series of 3.0 Watt Zener Diode Voltage Regulators with tight limits and better operating characteristics that reflect the superior capabilities of silicon-oxide passivated junctions. All this is in an axial-lead, transfer-molded plastic package that offers protection in all common environmental conditions.

  • Zener Voltage Range - 3.3 V to 200 V
  • ESD Rating of Class 3 (>16 KV) per Human Body Model
  • Surge Rating of 98 Watts @ 1 ms
  • Maximum Limits Guaranteed On Up To Six Electrical Parameters
  • Package No Larger Than the Conventional 1 Watt Package


Mechanical Characteristics:
  • CASE: Void free, transfer-molded, thermosetting plastic
  • FINISH: All external surfaces are corrosion resistant and leads are readily solderable
  • MAXIMUM LEAD TEMPERATURE FOR SOLDERING PURPOSES:230°C, 1/16, from the case for 10 seconds
  • POLARITY: Cathode indicated by polarity band
  • MOUNTING POSITION: Any
  • Pb-Free Packages are Available

H11AA1 Optocoupler, Phototransistor Output, AC Input, with Base Connection

H11AA1 Optocoupler, Phototransistor Output, AC Input, with Base Connection
An output transistor optocoupler (NPN phototransistor).

Widely used in applications:
- Detection of telephone line.
- AC line motors.
- PLC.
- Intrumentasi.

Features
AC or polarity insensitive input
Built-in reverse polarity input protection
I/O compatible with integrated circuits

General Specs:
Emitter voltage of 30 V (max)
Component output (transistor / triac) transistor
5300 Vrms isolation voltage
DIP-6 Packaging

TDA8950TH/N1 Audio Power Amplifier

NXP  TDA8950TH/N1  Audio Power Amplifier, D, 2 Channel, 150 W, ± 12.5V to ± 40V, HSSOP, 24 Pins

The TDA8950TH/N1 is a high efficiency, two channel class D audio power amplifier in 24 pin HSOP package. The typical output power is 2 x 150W with speaker load impedance of 4ohm. For each channel, the audio input signal is converted into a digital PWM signal using an analogue input stage and PWM modulator. The TDA8950TH/N1 contains high power switches, drivers, timing and handshaking between power switches along with some control logic. To ensure maximum system robustness, an advanced protection strategy has been implemented to provide overvoltage, overtemperature and overcurrent protection. Each of the two audio channels contains PWM modulator, analogue feedback loop and differential input stage.
  • Symmetrical operating supply voltage range from ±12.5V to ±40V
  • Low quiescent current consumption of 50mA
  • Stereo full differential inputs, can be used as stereo SE or mono BTL amplifier
  • Thermal foldback (TFB)
  • Smooth pop noise free start up and switch off
  • Zero dead time switching
  • Fixed gain of 30dB in SE and 36dB in BTL applications
  • BD modulation in BTL configuration
  • Fully short circuit proof across load
  • Ambient temperature range from -40°C to 85°C

Thursday, August 18, 2016

Sanfix 32 in 1 screwdriver set

SANFIX 32 in 1 screwdriver set

* PH0 - SL0-1
* PH1 - SL3-4
* PH2 - SL5-6
* PH3 - SL8-10
* HEX2mm - HEX2.5mm
* HEX3mm - HEX4mm
* HEX5mm - HEX6mm
* SR0 - SR1
* SR2 - SR3
* T5 - T30
* T6 - T40
* T10 - T15
* T20 - T25
* TH10 - TH20
* PZ1 - PZ2
* PZ0 - PZ3

Wednesday, August 17, 2016

OEM Switching Power Supply 12V / 5Amp

OEM Switching Power Supply 12V / 5Amp

features:
- AC to DC Power supply
- A wide input voltage range
- Small size, light weight, high efficiency
- Protection features: short circuit / overload
- Air cooling
- LED indicator
- 100% of full load testing
- Size: 244 x 137 x 70 (mm)

Technical parameters:
- Output voltage: 12 V
- Flow Output: 5A
- Output Power: 60 W
- Input Voltage: 85-230 VAC
- Input Freq: 47-63 Hz
- Output adjustment range: ± 10%
- Overload Protection: 105% -200%, automatically revived
- Over voltage protection: 115% -135%
- Short-circuit protection: automatic life kembal
- Time start output: <= 2 seconds @ 120VAC, <= 1 sec @ 230VAC
- Time keeping output:> = 10 milli-seconds @ 120 VAC,> = 20 milli-seconds @ 230 VAC
- Exodus dielectric:
Input-output: AC1500V, 1 minute
Input-chassis: AC1500, 1 minute
Input-chassis: DC500V, 1 minute
- Work environment: -10 ° C to 50 ° C, 20% -90% RH (no condensation)
- Safety standards: reference design EN / UL60950
- Electromagnetic compatibility standards: EN55022 Class B reference design

Tuesday, August 16, 2016

HKE HRS2H-S 24VDC DPDT Relay

Relay 24VDC with configuration DPDT (double-pole, double-throw) brand HKE.

  • Coil sensivity: 200mW
  • Number of pins 8 Pin
  • Dimensions 20.3 x 9.9 x 11.4 mm
  • configuration DPDT
  • Coil voltage 24VDC
  • Contact voltage 120VAC / 24VDC
  • Contact Flow 1A

June 2016 Single Board Computer Comparison

Do you want to buy a new single board computer to start building new things? Before doing that, go ahead and take a look at the ultimate hacker board comparison chart that tells you the major features and price of these Single Board Computers.

Raspberry Pi and Arduino are well-recognized single board computers, there are tons of other boards available if you want to start making new things and hacking.

Product Price ($) Vendor Processor Cores
86Duino Zero 39 DMP Vortex86EX 1x x86 @ 300MHz
A20-OlinuXino-Lime 37 Olimex Allwinner A20 2x A7 @ 1GHz
A20-OlinuXino-Lime2-EMMC 61 Olimex Allwinner A20 2x A7 @ 1GHz
A20-OlinuXino-Micro 61 Olimex Allwinner A20 2x A7 @ 1GHz
Andromeda Box Edge 75 Marvell, Arrow Marvell IAP140 4x A53 @ 1.2GHz
Arduino Industrial 101 39 Arduino Srl Qualcomm AR9331 1x MIPS @ 400MHz
Arduino Yún Mini 60 Arduino Srl Qualcomm AR9331 1x MIPS @ 400MHz
Arduino Tian 99 Arduino Srl Qualcomm AR9432 1x MIPS @ 560MHz
Samsung Exynos 4x A15 @ 1.8GHz +
Arndale Octa 199 InSignal, Pyrustek 5420 4x A7 @ 1.3GHz
Banana Pi M2 58 SinoVoip Allwinner A31 4x A7 @ 1GHz
Banana Pi M2+ 37 SinoVoip Allwinner H3 4x A7 @ 1.6GHz
Banana Pi M3 70 SinoVoip Allwinner A83T 8x A7 @ 2GHz
Banana Pro 48 LeMaker Allwinner A20 2x A7 @ 1GHz
BeagleBone Black 48 BeagleBoard.org TI Sitara AM3358 1x A8 @ 1GHz
BeagleBone Green 39 SeeedStudio TI Sitara AM3358 1x A8 @ 1GHz
BeagleBone Green Wireless 45 SeeedStudio TI Sitara AM3358 1x A8 @ 1GHz
Bubblegum-96 89 uCRobotics Actions S900 4x A53 @ 1.8GHz
Chip 9 Next Thing Allwinner R8 1x A8 @ 1GHz
1x ARM9 @
CloudBit 60 LittleBits Freescale i.MX233 454MHz
Creator CI40 156 Imagination Tech. Imagination CXT200 2x MIPS @ 550MHz
Cubieboard3 86 Cubieboard.org Allwinner A20 2x A7 @ 1GHz
4x A15 @ 2GHz +
Cubieboard4 125 Cubieboard.org Allwinner A80 4x A7 @ 1.3GHz
Cubieboard5 99 Cubieboard.org Allwinner H8 8x A7 @ 2GHz
DPT-Board 56 DPTechnics Qualcomm AR9331 1x MIPS @ 400MHz
Qualcomm
DragonBoard 410c 75 Qualcomm, Arrow Snapdragon 410 4x A53 @ 1.2GHz
Firefly FirePrime 99 Firefly Rockchip RK3128 4x A7 @ 1.3GHz
Firefly-RK3288 159 Firefly Rockchip RK3288 4x A17 @ 1.8GHz
Firefly-RK3288 Reload 189 Firefly Rockchip RK3288 4x A17 @ 1.8GHz
Galileo Gen 2 56 Intel Intel Quark X1000 1x x86 @ 400MHz
AMD, AMD G-Series
Gizmo 2 189 GizmoSphere GX210HA 2x x86 @ 1GHz
75 (99 with LeMaker,
HiKey 2GB) 96Boards.org HiSilicon Kirin 6220 8x A53 @ 1.2GHz
HobbitBoard 69 Wandboard.org NXP I.MX6 UL 1x A7 @ 528MHz
70 (with 1x/2x/4x A9 @ up to
HummingBoard-Base Solo) SolidRun NXP i.MX6 1.2GHz
85 (with 1x/2x/4x A9 @ up to
HummingBoard-Pro Solo) SolidRun NXP i.MX6 1.2GHz
102 (with 1x/2x/4x ARM @ up
HummingBoard-Edge Solo) SolidRun NXP i.MX6 to 1.2GHz
70 (with 1x/2x/4x ARM @ up
HummingBoard-Gate Solo) SolidRun NXP i.MX6 to 1.2GHz
Qualcomm
Inforce 6410Plus 143 Inforce Snapdragon 600 4x A15 @ 1.7GHz
2x x86 @ 500MHz +
Intel Edison Kit for Arduino 87 Intel Intel "Tangier" Atom Quark
LeMaker Guitar 45 LeMaker Actions S500 4x A9 @ 1.6GHz
SeeedStudio, MediaTek
LinkIt Smart 7688 13 MediaTek MT7688AN 1x MIPS @ 580MHz
LinkSprite Acadia V3 119 LinkSprite NXP i.MX6 Quad 4x A9 @ 1.2GHz
4x A15 @ 2GHz +
LinkSprite Arches 95 LinkSprite Allwinner A80 4x A7 @ 1.3GHz
HaoYu,
MarsBoard AM335x 75 MarsBoard.org TI AM3358 1x A8 @ 1GHz
HaoYu,
MarsBoard RK3066 58 MarsBoard.org Rockchip RK3066 2x A9 @ 1.6GHz
HaoYu,
MarsBoard RK3066 Pro 140 MarsBoard.org Rockchip RK3066 2x A9 @ 1.6GHz
Intel, ADI,
MinnowBoard Max Turbot 140 Minnowboard.org Intel Atom E3826 2x x86 @ 1.46GHz
NanoPC-T3 60 FriendlyARM Samsung S5P6818 8x A53 @ 1.4GHz
NanoPi M1 11 FriendlyARM Allwinner H3 4x A7 @ 1.2GHz
NanoPi M2 25 FriendlyARM Samsung S5P4418 4x A9 @ 1.4GHz
NanoPi M3 35 FriendlyARM Samsung S5P6818 8x A53 @ 1.4GHz
NanoPi2 Fire 23 FriendlyARM Samsung S5P4418 4x A9 @ 1.4GHz
Odroid-C0 27 Hardkernel Amlogic S805 4x A5 @ 1.5GHz
Odroid-C1+ 32 Hardkernel Amlogic S805 4x A5 @ 1.5GHz
Odroid-C2 40 Hardkernel Amlogic S905 4x A53 @ 2GHz
Samsung 4x A15 @ 2GHz +
Odroid-XU4 74 Hardkernel Exynos5422 4x A7 @1.4GHz
Orange Pi Lite 12 Shenzhen Xunlong Allwinner H3 4x A7 @ 1.2GHz
Orange Pi One 10 Shenzhen Xunlong Allwinner H3 4x A7 @ 1.2GHz
Orange Pi PC / PC Plus 15 Shenzhen Xunlong Allwinner H3 4x A7 @ 1.6GHz
Orange Pi Plus2 / Pluse2E 49 Shenzhen Xunlong Allwinner H3 4x A7 @ 1.6GHz)
Zilinx Zynq- 2x A7 @ 667MHz +
Parallella 99 Adapteva 7020/7010 FPGA
pcDuino Lite / Lite WiFi 29 LinkSprite Allwinner A10 1x A8 @ 1GHz
pcDuino3 Nano / Nano Lite 40 LinkSprite Allwinner A20 2x A7 @ 1GHz
pcDuino8 Uno 49 LinkSprite Allwinner H8 8x A7 @ 2GHz
Pine A64 15 Pine64 Allwinner A64 4x A53 @ 1.2GHz
PixiePro 100 Code NXP i.MX6 Quad 4x A9 @ 1GHz
Radxa Rock Lite / Rock Pro 59 Radxa Rockchip RK3188 4x A9 @ 1.6GHz
Radxa Rock 2 Square 129 Radxa Rockchip RK3288 4x A17 @ 1.6GHz
Broadcom
Raspberry Pi Zero 14 Rpi Trading BCM2835 1x A8 @ 1GHz
Raspberry Pi 2 Model B 35 Rpi Trading BCM2836 4x A7 @ 900MHz
Broadcom
Raspberry Pi 3 Model B 35 Rpi Trading BCM43437 4x A53 @ 1.2GHz
Rico Board 99 MYIR TI AM437x 1x A9 @ 1GHz
Newark,
RioTboard 79 RioTboard.org NXP i.MX6 Solo 1x A9 @ 1GHz
Roseapple Pi 50 Roseapplepi.org Actions S500 4x A9 @ 1.6GHz
SAMA5D4 Xplained 94 Newark, Atmel Atmel SAMA5D4 1x A5 @ 528MHz
Seeeduino Cloud 70 SeeedStudio Qualcomm AR9331 1x MIPS @ 400MHz
Xilinx Zynq- 2x A9 @ 667MHz +
Snickerdoodle 62 Krtkl 7010/7020 FPGA
Udoo Neo 50 Udoo (Seco) NXP i.MX6 SoloX 1x A9 @ 1GHz)
NXP i.MX6
Udoo Quad/Dual/Dual Basic 99 Udoo (Seco) Dual/Quad 2x/4x A9 @ 1GHz
USB Armory 130 Inverse Path NXP i.MX53 1x A8 @ 800MHz
1x, 2x, or 4x A9
Wandboard 79 Wandboard.org NXP i.MX6 @1GHz
Xilinx Zynq- 2x ARM @ 667MHz
Z-turn Board 99 MYIR 7010/7020 + FPGA


Download Complete PDF file here